+-- Do proper aligning for subsequent lines. For example, in
+-- foo = bar
+-- | baz
+-- We replace the spaces in the second line with a skip with the same with as
+-- "foo ", to align the | with the =.
+-- For this, we keep a table "indentlines", which contains all previous lines
+-- with smaller indent levels that are still "in scope" (e.g., have not yet
+-- been followed by a line with a smaller indent level). For example:
+-- line1
+-- line2
+-- line3
+-- line4
+-- line5
+-- After the last line, the table will contain:
+-- { 0 = "line1", 2 = " line4", 4 = " line5"}
+-- In other words, line3 is no longer in scope since it is "hidden" by
+-- line4, and line is no longer in scope since it is replaced by line4.
+local function do_indent(line)
+ newind, rest = utf.match(line, '^(%s*)(.*)')
+ prev = -1
+ -- Loop all the previous lines
+ for indent, unused in pairs(indentlines) do
+ if indent > #newind then
+ -- Remove any lines with a larger indent
+ indentlines[indent] = nil
+ elseif indent < #newind and indent > prev then
+ -- Find the last line (e.g, with the highest indent) with an
+ -- indent smaller than the new indent. This is the line from which
+ -- we need to copy the indent.
+ prev = indent
+ end
+ end
+
+ -- Always store this line, possibly overwriting a previous line with the
+ -- same indent
+ indentlines[#newind] = line
+
+ if prev ~= -1 then
+ -- If there is a previous line with a smaller indent, make sure we
+ -- align with it. We do this by taking a prefix from that previous
+ -- line just as long as our indent. This gives us a bunch of
+ -- whitespace, with a few non-whitespace characters. We find out the
+ -- width of this prefix, and put whitespace just as wide as that
+ -- prefix before the current line, instead of the whitespace
+ -- characters that were there.
+ -- Doing this is slightly risky, since the prefix might contain
+ -- unfinished markup (e.g., \foo{bar without the closing }). We might
+ -- need to solve this later.
+ copyind = utf.sub(indentlines[prev], 1, #newind)
+ setwidth = "\\setwidthof{" .. copyind .. "}\\to\\pretlamalignwidth"
+ hskip = "\\hskip\\pretlamalignwidth"
+ return "{" .. setwidth .. hskip .. "}" .. rest
+ end
+ -- No previous line? Just return the unmodified line then
+ return line
+end
+
+
+-- Mark the begin of a block of lambda formatted buffers or expressions. This
+-- means that, until you call end_of_block again, the subscript bases are
+-- shared. For example, if you have \lam{y1} some text \lam{yn} within a
+-- single block, the yn will properly get subscripted. Be sure to call
+-- end_of_block again!
+--
+-- Blocks can be partially nested, meaning that the block
+-- won't be closed until end_of_block was called exactly as often as
+-- begin_of_block. However, subscripts from the inner block can still
+-- influence subscripts in the outer block.
+function vis.begin_of_block()
+ vis.begin_of_display()
+ in_block = in_block + 1
+end
+
+-- Ends the current block
+function vis.end_of_block()
+ in_block = in_block - 1
+end
+
+function vis.begin_of_display()
+ if in_block == 0 then
+ -- Initially allow subscripts using _ or just appending a number (later,
+ -- we will add extra patterns here.
+ submatches = {"^(%a*)_([%a%d,]+)$", "^(%a+)(%d+)$"}
+ -- This stores all the bases we've encountered so far (to prevent
+ -- duplicates). For each of them there will be a pattern in submatches
+ -- above.
+ bases = {}
+ end
+ indentlines = {}