--- /dev/null
+## Dovecot configuration file
+
+# If you're in a hurry, see http://wiki.dovecot.org/QuickConfiguration
+
+# "dovecot -n" command gives a clean output of the changed settings. Use it
+# instead of copy&pasting this file when posting to the Dovecot mailing list.
+
+# '#' character and everything after it is treated as comments. Extra spaces
+# and tabs are ignored. If you want to use either of these explicitly, put the
+# value inside quotes, eg.: key = "# char and trailing whitespace "
+
+# Default values are shown for each setting, it's not required to uncomment
+# any of the lines. Exception to this are paths, they're just examples with
+# the real defaults being based on configure options. The paths listed here
+# are for configure --prefix=/usr --sysconfdir=/etc --localstatedir=/var
+# --with-ssldir=/etc/ssl
+
+# Base directory where to store runtime data.
+#base_dir = /var/run/dovecot/
+
+# Protocols we want to be serving: imap imaps pop3 pop3s managesieve
+# If you only want to use dovecot-auth, you can set this to "none".
+#protocols = imap imaps
+
+# A space separated list of IP or host addresses where to listen in for
+# connections. "*" listens in all IPv4 interfaces. "[::]" listens in all IPv6
+# interfaces. Use "*, [::]" for listening both IPv4 and IPv6.
+#
+# If you want to specify ports for each service, you will need to configure
+# these settings inside the protocol imap/pop3/managesieve { ... } section,
+# so you can specify different ports for IMAP/POP3/MANAGESIEVE. For example:
+# protocol imap {
+# listen = *:10143
+# ssl_listen = *:10943
+# ..
+# }
+# protocol pop3 {
+# listen = *:10100
+# ..
+# }
+# protocol managesieve {
+# listen = *:12000
+# ..
+# }
+#listen = *
+
+# Disable LOGIN command and all other plaintext authentications unless
+# SSL/TLS is used (LOGINDISABLED capability). Note that if the remote IP
+# matches the local IP (ie. you're connecting from the same computer), the
+# connection is considered secure and plaintext authentication is allowed.
+#disable_plaintext_auth = yes
+
+# Should all IMAP and POP3 processes be killed when Dovecot master process
+# shuts down. Setting this to "no" means that Dovecot can be upgraded without
+# forcing existing client connections to close (although that could also be
+# a problem if the upgrade is eg. because of a security fix). This however
+# means that after master process has died, the client processes can't write
+# to log files anymore.
+#shutdown_clients = yes
+
+##
+## Logging
+##
+
+# Log file to use for error messages, instead of sending them to syslog.
+# /dev/stderr can be used to log into stderr.
+#log_path =
+
+# Log file to use for informational and debug messages.
+# Default is the same as log_path.
+#info_log_path =
+
+# Prefix for each line written to log file. % codes are in strftime(3)
+# format.
+#log_timestamp = "%b %d %H:%M:%S "
+
+# Syslog facility to use if you're logging to syslog. Usually if you don't
+# want to use "mail", you'll use local0..local7. Also other standard
+# facilities are supported.
+#syslog_facility = mail
+
+##
+## SSL settings
+##
+
+# IP or host address where to listen in for SSL connections. Remember to also
+# add imaps and/or pop3s to protocols setting. Defaults to same as "listen"
+# setting if not specified.
+#ssl_listen =
+
+# SSL/TLS support: yes, no, required. <doc/wiki/SSL>
+#ssl = yes
+
+# PEM encoded X.509 SSL/TLS certificate and private key. They're opened before
+# dropping root privileges, so keep the key file unreadable by anyone but
+# root. Included doc/mkcert.sh can be used to easily generate self-signed
+# certificate, just make sure to update the domains in dovecot-openssl.cnf
+#ssl_cert_file = /etc/ssl/certs/dovecot.pem
+#ssl_key_file = /etc/ssl/private/dovecot.pem
+
+# If key file is password protected, give the password here. Alternatively
+# give it when starting dovecot with -p parameter. Since this file is often
+# world-readable, you may want to place this setting instead to a different
+# root owned 0600 file by using !include_try <path>.
+#ssl_key_password =
+
+# File containing trusted SSL certificate authorities. Set this only if you
+# intend to use ssl_verify_client_cert=yes. The CAfile should contain the
+# CA-certificate(s) followed by the matching CRL(s).
+#ssl_ca_file =
+
+# Request client to send a certificate. If you also want to require it, set
+# ssl_require_client_cert=yes in auth section.
+#ssl_verify_client_cert = no
+
+# Which field from certificate to use for username. commonName and
+# x500UniqueIdentifier are the usual choices. You'll also need to set
+# ssl_username_from_cert=yes.
+#ssl_cert_username_field = commonName
+
+# How often to regenerate the SSL parameters file. Generation is quite CPU
+# intensive operation. The value is in hours, 0 disables regeneration
+# entirely.
+#ssl_parameters_regenerate = 168
+
+# SSL ciphers to use
+#ssl_cipher_list = ALL:!LOW:!SSLv2
+
+# Show protocol level SSL errors.
+#verbose_ssl = no
+
+##
+## Login processes
+##
+
+# <doc/wiki/LoginProcess.txt>
+
+# Directory where authentication process places authentication UNIX sockets
+# which login needs to be able to connect to. The sockets are created when
+# running as root, so you don't have to worry about permissions. Note that
+# everything in this directory is deleted when Dovecot is started.
+#login_dir = /var/run/dovecot/login
+
+# chroot login process to the login_dir. Only reason not to do this is if you
+# wish to run the whole Dovecot without roots. <doc/wiki/Rootless.txt>
+#login_chroot = yes
+
+# User to use for the login process. Create a completely new user for this,
+# and don't use it anywhere else. The user must also belong to a group where
+# only it has access, it's used to control access for authentication process.
+# Note that this user is NOT used to access mails. <doc/wiki/UserIds.txt>
+#login_user = dovecot
+
+# Set max. process size in megabytes. If you don't use
+# login_process_per_connection you might need to grow this.
+#login_process_size = 64
+
+# Should each login be processed in it's own process (yes), or should one
+# login process be allowed to process multiple connections (no)? Yes is more
+# secure, espcially with SSL/TLS enabled. No is faster since there's no need
+# to create processes all the time.
+#login_process_per_connection = yes
+
+# Number of login processes to keep for listening new connections.
+#login_processes_count = 3
+
+# Maximum number of login processes to create. The listening process count
+# usually stays at login_processes_count, but when multiple users start logging
+# in at the same time more extra processes are created. To prevent fork-bombing
+# we check only once in a second if new processes should be created - if all
+# of them are used at the time, we double their amount until the limit set by
+# this setting is reached.
+#login_max_processes_count = 128
+
+# Maximum number of connections allowed per each login process. This setting
+# is used only if login_process_per_connection=no. Once the limit is reached,
+# the process notifies master so that it can create a new login process.
+#login_max_connections = 256
+
+# Greeting message for clients.
+#login_greeting = Dovecot ready.
+
+# Space separated list of trusted network ranges. Connections from these
+# IPs are allowed to override their IP addresses and ports (for logging and
+# for authentication checks). disable_plaintext_auth is also ignored for
+# these networks. Typically you'd specify your IMAP proxy servers here.
+#login_trusted_networks =
+
+# Space-separated list of elements we want to log. The elements which have
+# a non-empty variable value are joined together to form a comma-separated
+# string.
+#login_log_format_elements = user=<%u> method=%m rip=%r lip=%l %c
+
+# Login log format. %$ contains login_log_format_elements string, %s contains
+# the data we want to log.
+#login_log_format = %$: %s
+
+##
+## Mailbox locations and namespaces
+##
+
+# Location for users' mailboxes. This is the same as the old default_mail_env
+# setting. The default is empty, which means that Dovecot tries to find the
+# mailboxes automatically. This won't work if the user doesn't have any mail
+# yet, so you should explicitly tell Dovecot the full location.
+#
+# If you're using mbox, giving a path to the INBOX file (eg. /var/mail/%u)
+# isn't enough. You'll also need to tell Dovecot where the other mailboxes are
+# kept. This is called the "root mail directory", and it must be the first
+# path given in the mail_location setting.
+#
+# There are a few special variables you can use, eg.:
+#
+# %u - username
+# %n - user part in user@domain, same as %u if there's no domain
+# %d - domain part in user@domain, empty if there's no domain
+# %h - home directory
+#
+# See doc/wiki/Variables.txt for full list. Some examples:
+#
+# mail_location = maildir:~/Maildir
+# mail_location = mbox:~/mail:INBOX=/var/mail/%u
+# mail_location = mbox:/var/mail/%d/%1n/%n:INDEX=/var/indexes/%d/%1n/%n
+#
+# <doc/wiki/MailLocation.txt>
+#
+#mail_location =
+
+# If you need to set multiple mailbox locations or want to change default
+# namespace settings, you can do it by defining namespace sections.
+#
+# You can have private, shared and public namespaces. Private namespaces
+# are for user's personal mails. Shared namespaces are for accessing other
+# users' mailboxes that have been shared. Public namespaces are for shared
+# mailboxes that are managed by sysadmin. If you create any shared or public
+# namespaces you'll typically want to enable ACL plugin also, otherwise all
+# users can access all the shared mailboxes, assuming they have permissions
+# on filesystem level to do so.
+#
+# REMEMBER: If you add any namespaces, the default namespace must be added
+# explicitly, ie. mail_location does nothing unless you have a namespace
+# without a location setting. Default namespace is simply done by having a
+# namespace with empty prefix.
+#namespace private {
+ # Hierarchy separator to use. You should use the same separator for all
+ # namespaces or some clients get confused. '/' is usually a good one.
+ # The default however depends on the underlying mail storage format.
+ #separator =
+
+ # Prefix required to access this namespace. This needs to be different for
+ # all namespaces. For example "Public/".
+ #prefix =
+
+ # Physical location of the mailbox. This is in same format as
+ # mail_location, which is also the default for it.
+ #location =
+
+ # There can be only one INBOX, and this setting defines which namespace
+ # has it.
+ #inbox = no
+
+ # If namespace is hidden, it's not advertised to clients via NAMESPACE
+ # extension. You'll most likely also want to set list=no. This is mostly
+ # useful when converting from another server with different namespaces which
+ # you want to deprecate but still keep working. For example you can create
+ # hidden namespaces with prefixes "~/mail/", "~%u/mail/" and "mail/".
+ #hidden = yes
+
+ # Show the mailboxes under this namespace with LIST command. This makes the
+ # namespace visible for clients that don't support NAMESPACE extension.
+ # "children" value lists child mailboxes, but hides the namespace prefix.
+ #list = yes
+
+ # Namespace handles its own subscriptions. If set to "no", the parent
+ # namespace handles them (empty prefix should always have this as "yes")
+ #subscriptions = yes
+#}
+
+# Example shared namespace configuration
+#namespace shared {
+ #separator = /
+
+ # Mailboxes are visible under "shared/user@domain/"
+ # %%n, %%d and %%u are expanded to the destination user.
+ #prefix = shared/%%u/
+
+ # Mail location for other users' mailboxes. Note that %variables and ~/
+ # expands to the logged in user's data. %%n, %%d, %%u and %%h expand to the
+ # destination user's data.
+ #location = maildir:%%h/Maildir:INDEX=~/Maildir/shared/%%u
+
+ # Use the default namespace for saving subscriptions.
+ #subscriptions = no
+
+ # List the shared/ namespace only if there are visible shared mailboxes.
+ #list = children
+#}
+
+# System user and group used to access mails. If you use multiple, userdb
+# can override these by returning uid or gid fields. You can use either numbers
+# or names. <doc/wiki/UserIds>
+#mail_uid =
+#mail_gid =
+
+# Group to enable temporarily for privileged operations. Currently this is
+# used only with INBOX when either its initial creation or dotlocking fails.
+# Typically this is set to "mail" to give access to /var/mail.
+#mail_privileged_group =
+
+# Grant access to these supplementary groups for mail processes. Typically
+# these are used to set up access to shared mailboxes. Note that it may be
+# dangerous to set these if users can create symlinks (e.g. if "mail" group is
+# set here, ln -s /var/mail ~/mail/var could allow a user to delete others'
+# mailboxes, or ln -s /secret/shared/box ~/mail/mybox would allow reading it).
+#mail_access_groups =
+
+# Allow full filesystem access to clients. There's no access checks other than
+# what the operating system does for the active UID/GID. It works with both
+# maildir and mboxes, allowing you to prefix mailboxes names with eg. /path/
+# or ~user/.
+#mail_full_filesystem_access = no
+
+##
+## Mail processes
+##
+
+# Enable mail process debugging. This can help you figure out why Dovecot
+# isn't finding your mails.
+#mail_debug = no
+
+# Log prefix for mail processes. See doc/wiki/Variables.txt for list of
+# possible variables you can use.
+#mail_log_prefix = "%Us(%u): "
+
+# Max. number of lines a mail process is allowed to log per second before it's
+# throttled. 0 means unlimited. Typically there's no need to change this
+# unless you're using mail_log plugin, which may log a lot. This setting is
+# ignored while mail_debug=yes to avoid pointless throttling.
+#mail_log_max_lines_per_sec = 10
+
+# Don't use mmap() at all. This is required if you store indexes to shared
+# filesystems (NFS or clustered filesystem).
+#mmap_disable = no
+
+# Rely on O_EXCL to work when creating dotlock files. NFS supports O_EXCL
+# since version 3, so this should be safe to use nowadays by default.
+#dotlock_use_excl = yes
+
+# Don't use fsync() or fdatasync() calls. This makes the performance better
+# at the cost of potential data loss if the server (or the file server)
+# goes down.
+#fsync_disable = no
+
+# Mail storage exists in NFS. Set this to yes to make Dovecot flush NFS caches
+# whenever needed. If you're using only a single mail server this isn't needed.
+#mail_nfs_storage = no
+# Mail index files also exist in NFS. Setting this to yes requires
+# mmap_disable=yes and fsync_disable=no.
+#mail_nfs_index = no
+
+# Locking method for index files. Alternatives are fcntl, flock and dotlock.
+# Dotlocking uses some tricks which may create more disk I/O than other locking
+# methods. NFS users: flock doesn't work, remember to change mmap_disable.
+#lock_method = fcntl
+
+# Drop all privileges before exec()ing the mail process. This is mostly
+# meant for debugging, otherwise you don't get core dumps. It could be a small
+# security risk if you use single UID for multiple users, as the users could
+# ptrace() each others processes then.
+#mail_drop_priv_before_exec = no
+
+# Show more verbose process titles (in ps). Currently shows user name and
+# IP address. Useful for seeing who are actually using the IMAP processes
+# (eg. shared mailboxes or if same uid is used for multiple accounts).
+#verbose_proctitle = no
+
+# Valid UID range for users, defaults to 500 and above. This is mostly
+# to make sure that users can't log in as daemons or other system users.
+# Note that denying root logins is hardcoded to dovecot binary and can't
+# be done even if first_valid_uid is set to 0.
+#first_valid_uid = 500
+#last_valid_uid = 0
+
+# Valid GID range for users, defaults to non-root/wheel. Users having
+# non-valid GID as primary group ID aren't allowed to log in. If user
+# belongs to supplementary groups with non-valid GIDs, those groups are
+# not set.
+#first_valid_gid = 1
+#last_valid_gid = 0
+
+# Maximum number of running mail processes. When this limit is reached,
+# new users aren't allowed to log in.
+#max_mail_processes = 512
+
+# Set max. process size in megabytes. Most of the memory goes to mmap()ing
+# files, so it shouldn't harm much even if this limit is set pretty high.
+#mail_process_size = 256
+
+# Maximum allowed length for mail keyword name. It's only forced when trying
+# to create new keywords.
+#mail_max_keyword_length = 50
+
+# ':' separated list of directories under which chrooting is allowed for mail
+# processes (ie. /var/mail will allow chrooting to /var/mail/foo/bar too).
+# This setting doesn't affect login_chroot, mail_chroot or auth chroot
+# settings. If this setting is empty, "/./" in home dirs are ignored.
+# WARNING: Never add directories here which local users can modify, that
+# may lead to root exploit. Usually this should be done only if you don't
+# allow shell access for users. <doc/wiki/Chrooting.txt>
+#valid_chroot_dirs =
+
+# Default chroot directory for mail processes. This can be overridden for
+# specific users in user database by giving /./ in user's home directory
+# (eg. /home/./user chroots into /home). Note that usually there is no real
+# need to do chrooting, Dovecot doesn't allow users to access files outside
+# their mail directory anyway. If your home directories are prefixed with
+# the chroot directory, append "/." to mail_chroot. <doc/wiki/Chrooting.txt>
+#mail_chroot =
+
+##
+## Mailbox handling optimizations
+##
+
+# The minimum number of mails in a mailbox before updates are done to cache
+# file. This allows optimizing Dovecot's behavior to do less disk writes at
+# the cost of more disk reads.
+#mail_cache_min_mail_count = 0
+
+# When IDLE command is running, mailbox is checked once in a while to see if
+# there are any new mails or other changes. This setting defines the minimum
+# time in seconds to wait between those checks. Dovecot can also use dnotify,
+# inotify and kqueue to find out immediately when changes occur.
+#mailbox_idle_check_interval = 30
+
+# Save mails with CR+LF instead of plain LF. This makes sending those mails
+# take less CPU, especially with sendfile() syscall with Linux and FreeBSD.
+# But it also creates a bit more disk I/O which may just make it slower.
+# Also note that if other software reads the mboxes/maildirs, they may handle
+# the extra CRs wrong and cause problems.
+#mail_save_crlf = no
+
+##
+## Maildir-specific settings
+##
+
+# By default LIST command returns all entries in maildir beginning with a dot.
+# Enabling this option makes Dovecot return only entries which are directories.
+# This is done by stat()ing each entry, so it causes more disk I/O.
+# (For systems setting struct dirent->d_type, this check is free and it's
+# done always regardless of this setting)
+#maildir_stat_dirs = no
+
+# When copying a message, do it with hard links whenever possible. This makes
+# the performance much better, and it's unlikely to have any side effects.
+#maildir_copy_with_hardlinks = yes
+
+# When copying a message, try to preserve the base filename. Only if the
+# destination mailbox already contains the same name (ie. the mail is being
+# copied there twice), a new name is given. The destination filename check is
+# done only by looking at dovecot-uidlist file, so if something outside
+# Dovecot does similar filename preserving copies, you may run into problems.
+# NOTE: This setting requires maildir_copy_with_hardlinks = yes to work.
+#maildir_copy_preserve_filename = no
+
+# Assume Dovecot is the only MUA accessing Maildir: Scan cur/ directory only
+# when its mtime changes unexpectedly or when we can't find the mail otherwise.
+#maildir_very_dirty_syncs = no
+
+##
+## mbox-specific settings
+##
+
+# Which locking methods to use for locking mbox. There are four available:
+# dotlock: Create <mailbox>.lock file. This is the oldest and most NFS-safe
+# solution. If you want to use /var/mail/ like directory, the users
+# will need write access to that directory.
+# dotlock_try: Same as dotlock, but if it fails because of permissions or
+# because there isn't enough disk space, just skip it.
+# fcntl : Use this if possible. Works with NFS too if lockd is used.
+# flock : May not exist in all systems. Doesn't work with NFS.
+# lockf : May not exist in all systems. Doesn't work with NFS.
+#
+# You can use multiple locking methods; if you do the order they're declared
+# in is important to avoid deadlocks if other MTAs/MUAs are using multiple
+# locking methods as well. Some operating systems don't allow using some of
+# them simultaneously.
+#mbox_read_locks = fcntl
+#mbox_write_locks = dotlock fcntl
+
+# Maximum time in seconds to wait for lock (all of them) before aborting.
+#mbox_lock_timeout = 300
+
+# If dotlock exists but the mailbox isn't modified in any way, override the
+# lock file after this many seconds.
+#mbox_dotlock_change_timeout = 120
+
+# When mbox changes unexpectedly we have to fully read it to find out what
+# changed. If the mbox is large this can take a long time. Since the change
+# is usually just a newly appended mail, it'd be faster to simply read the
+# new mails. If this setting is enabled, Dovecot does this but still safely
+# fallbacks to re-reading the whole mbox file whenever something in mbox isn't
+# how it's expected to be. The only real downside to this setting is that if
+# some other MUA changes message flags, Dovecot doesn't notice it immediately.
+# Note that a full sync is done with SELECT, EXAMINE, EXPUNGE and CHECK
+# commands.
+#mbox_dirty_syncs = yes
+
+# Like mbox_dirty_syncs, but don't do full syncs even with SELECT, EXAMINE,
+# EXPUNGE or CHECK commands. If this is set, mbox_dirty_syncs is ignored.
+#mbox_very_dirty_syncs = no
+
+# Delay writing mbox headers until doing a full write sync (EXPUNGE and CHECK
+# commands and when closing the mailbox). This is especially useful for POP3
+# where clients often delete all mails. The downside is that our changes
+# aren't immediately visible to other MUAs.
+#mbox_lazy_writes = yes
+
+# If mbox size is smaller than this (in kilobytes), don't write index files.
+# If an index file already exists it's still read, just not updated.
+#mbox_min_index_size = 0
+
+##
+## dbox-specific settings
+##
+
+# Maximum dbox file size in kilobytes until it's rotated.
+#dbox_rotate_size = 2048
+
+# Minimum dbox file size in kilobytes before it's rotated
+# (overrides dbox_rotate_days)
+#dbox_rotate_min_size = 16
+
+# Maximum dbox file age in days until it's rotated. Day always begins from
+# midnight, so 1 = today, 2 = yesterday, etc. 0 = check disabled.
+#dbox_rotate_days = 0
+
+##
+## IMAP specific settings
+##
+
+protocol imap {
+ # Login executable location.
+ #login_executable = /usr/libexec/dovecot/imap-login
+
+ # IMAP executable location. Changing this allows you to execute other
+ # binaries before the imap process is executed.
+ #
+ # This would write rawlogs into ~/dovecot.rawlog/ directory:
+ # mail_executable = /usr/libexec/dovecot/rawlog /usr/libexec/dovecot/imap
+ #
+ # This would attach gdb into the imap process and write backtraces into
+ # /tmp/gdbhelper.* files:
+ # mail_executable = /usr/libexec/dovecot/gdbhelper /usr/libexec/dovecot/imap
+ #
+ #mail_executable = /usr/libexec/dovecot/imap
+
+ # Maximum IMAP command line length in bytes. Some clients generate very long
+ # command lines with huge mailboxes, so you may need to raise this if you get
+ # "Too long argument" or "IMAP command line too large" errors often.
+ #imap_max_line_length = 65536
+
+ # Maximum number of IMAP connections allowed for a user from each IP address.
+ # NOTE: The username is compared case-sensitively.
+ #mail_max_userip_connections = 10
+
+ # Support for dynamically loadable plugins. mail_plugins is a space separated
+ # list of plugins to load.
+ #mail_plugins =
+ #mail_plugin_dir = /usr/lib/dovecot/imap
+
+ # IMAP logout format string:
+ # %i - total number of bytes read from client
+ # %o - total number of bytes sent to client
+ #imap_logout_format = bytes=%i/%o
+
+ # Override the IMAP CAPABILITY response.
+ #imap_capability =
+
+ # ID field names and values to send to clients. Using * as the value makes
+ # Dovecot use the default value. The following fields have default values
+ # currently: name, version, os, os-version, support-url, support-email.
+ #imap_id_send =
+
+ # ID fields sent by client to log. * means everything.
+ #imap_id_log =
+
+ # Workarounds for various client bugs:
+ # delay-newmail:
+ # Send EXISTS/RECENT new mail notifications only when replying to NOOP
+ # and CHECK commands. Some clients ignore them otherwise, for example OSX
+ # Mail (<v2.1). Outlook Express breaks more badly though, without this it
+ # may show user "Message no longer in server" errors. Note that OE6 still
+ # breaks even with this workaround if synchronization is set to
+ # "Headers Only".
+ # netscape-eoh:
+ # Netscape 4.x breaks if message headers don't end with the empty "end of
+ # headers" line. Normally all messages have this, but setting this
+ # workaround makes sure that Netscape never breaks by adding the line if
+ # it doesn't exist. This is done only for FETCH BODY[HEADER.FIELDS..]
+ # commands. Note that RFC says this shouldn't be done.
+ # tb-extra-mailbox-sep:
+ # With mbox storage a mailbox can contain either mails or submailboxes,
+ # but not both. Thunderbird separates these two by forcing server to
+ # accept '/' suffix in mailbox names in subscriptions list.
+ # The list is space-separated.
+ #imap_client_workarounds =
+}
+
+##
+## POP3 specific settings
+##
+
+protocol pop3 {
+ # Login executable location.
+ #login_executable = /usr/libexec/dovecot/pop3-login
+
+ # POP3 executable location. See IMAP's mail_executable above for examples
+ # how this could be changed.
+ #mail_executable = /usr/libexec/dovecot/pop3
+
+ # Don't try to set mails non-recent or seen with POP3 sessions. This is
+ # mostly intended to reduce disk I/O. With maildir it doesn't move files
+ # from new/ to cur/, with mbox it doesn't write Status-header.
+ #pop3_no_flag_updates = no
+
+ # Support LAST command which exists in old POP3 specs, but has been removed
+ # from new ones. Some clients still wish to use this though. Enabling this
+ # makes RSET command clear all \Seen flags from messages.
+ #pop3_enable_last = no
+
+ # If mail has X-UIDL header, use it as the mail's UIDL.
+ #pop3_reuse_xuidl = no
+
+ # Keep the mailbox locked for the entire POP3 session.
+ #pop3_lock_session = no
+
+ # POP3 UIDL (unique mail identifier) format to use. You can use following
+ # variables, along with the variable modifiers described in
+ # doc/wiki/Variables.txt (e.g. %Uf for the filename in uppercase)
+ #
+ # %v - Mailbox's IMAP UIDVALIDITY
+ # %u - Mail's IMAP UID
+ # %m - MD5 sum of the mailbox headers in hex (mbox only)
+ # %f - filename (maildir only)
+ #
+ # If you want UIDL compatibility with other POP3 servers, use:
+ # UW's ipop3d : %08Xv%08Xu
+ # Courier : %f or %v-%u (both might be used simultaneosly)
+ # Cyrus (<= 2.1.3) : %u
+ # Cyrus (>= 2.1.4) : %v.%u
+ # Dovecot v0.99.x : %v.%u
+ # tpop3d : %Mf
+ #
+ # Note that Outlook 2003 seems to have problems with %v.%u format which was
+ # Dovecot's default, so if you're building a new server it would be a good
+ # idea to change this. %08Xu%08Xv should be pretty fail-safe.
+ #
+ #pop3_uidl_format = %08Xu%08Xv
+
+ # POP3 logout format string:
+ # %i - total number of bytes read from client
+ # %o - total number of bytes sent to client
+ # %t - number of TOP commands
+ # %p - number of bytes sent to client as a result of TOP command
+ # %r - number of RETR commands
+ # %b - number of bytes sent to client as a result of RETR command
+ # %d - number of deleted messages
+ # %m - number of messages (before deletion)
+ # %s - mailbox size in bytes (before deletion)
+ #pop3_logout_format = top=%t/%p, retr=%r/%b, del=%d/%m, size=%s
+
+ # Maximum number of POP3 connections allowed for a user from each IP address.
+ # NOTE: The username is compared case-sensitively.
+ #mail_max_userip_connections = 3
+
+ # Support for dynamically loadable plugins. mail_plugins is a space separated
+ # list of plugins to load.
+ #mail_plugins =
+ #mail_plugin_dir = /usr/lib/dovecot/pop3
+
+ # Workarounds for various client bugs:
+ # outlook-no-nuls:
+ # Outlook and Outlook Express hang if mails contain NUL characters.
+ # This setting replaces them with 0x80 character.
+ # oe-ns-eoh:
+ # Outlook Express and Netscape Mail breaks if end of headers-line is
+ # missing. This option simply sends it if it's missing.
+ # The list is space-separated.
+ #pop3_client_workarounds =
+}
+
+##
+## MANAGESIEVE specific settings
+##
+
+protocol managesieve {
+ # Login executable location.
+ #login_executable = /usr/libexec/dovecot/managesieve-login
+
+ # MANAGESIEVE executable location. See IMAP's mail_executable above for
+ # examples how this could be changed.
+ #mail_executable = /usr/libexec/dovecot/managesieve
+
+ # Maximum MANAGESIEVE command line length in bytes. This setting is
+ # directly borrowed from IMAP. But, since long command lines are very
+ # unlikely with MANAGESIEVE, changing this will not be very useful.
+ #managesieve_max_line_length = 65536
+
+ # If, for some inobvious reason, the sieve_storage remains unset, the
+ # managesieve daemon uses the specification of the mail_location to find out
+ # where to store the sieve files (see explaination in README.managesieve).
+ # The example below, when uncommented, overrides any global mail_location
+ # specification and stores all the scripts in '~/mail/sieve' if sieve_storage
+ # is unset. However, you should always use the sieve_storage setting.
+ # mail_location = mbox:~/mail
+
+ # To fool managesieve clients that are focused on timesieved you can
+ # specify the IMPLEMENTATION capability that the dovecot reports to clients
+ # (default: dovecot).
+ #managesieve_implementation_string = Cyrus timsieved v2.2.13
+}
+
+##
+## LDA specific settings
+##
+
+protocol lda {
+ # Address to use when sending rejection mails.
+ postmaster_address = postmaster@example.com
+
+ # Hostname to use in various parts of sent mails, eg. in Message-Id.
+ # Default is the system's real hostname.
+ #hostname =
+
+ # Support for dynamically loadable plugins. mail_plugins is a space separated
+ # list of plugins to load.
+ #mail_plugins =
+ #mail_plugin_dir = /usr/lib/dovecot/lda
+
+ # If user is over quota, return with temporary failure instead of
+ # bouncing the mail.
+ #quota_full_tempfail = no
+
+ # Format to use for logging mail deliveries. You can use variables:
+ # %$ - Delivery status message (e.g. "saved to INBOX")
+ # %m - Message-ID
+ # %s - Subject
+ # %f - From address
+ #deliver_log_format = msgid=%m: %$
+
+ # Binary to use for sending mails.
+ #sendmail_path = /usr/lib/sendmail
+
+ # Subject: header to use for rejection mails. You can use the same variables
+ # as for rejection_reason below.
+ #rejection_subject = Rejected: %s
+
+ # Human readable error message for rejection mails. You can use variables:
+ # %n = CRLF, %r = reason, %s = original subject, %t = recipient
+ #rejection_reason = Your message to <%t> was automatically rejected:%n%r
+
+ # UNIX socket path to master authentication server to find users.
+ #auth_socket_path = /var/run/dovecot/auth-master
+}
+
+##
+## Authentication processes
+##
+
+# Executable location
+#auth_executable = /usr/libexec/dovecot/dovecot-auth
+
+# Set max. process size in megabytes.
+#auth_process_size = 256
+
+# Authentication cache size in kilobytes. 0 means it's disabled.
+# Note that bsdauth, PAM and vpopmail require cache_key to be set for caching
+# to be used.
+#auth_cache_size = 0
+# Time to live in seconds for cached data. After this many seconds the cached
+# record is no longer used, *except* if the main database lookup returns
+# internal failure. We also try to handle password changes automatically: If
+# user's previous authentication was successful, but this one wasn't, the
+# cache isn't used. For now this works only with plaintext authentication.
+#auth_cache_ttl = 3600
+# TTL for negative hits (user not found). 0 disables caching them completely.
+#auth_cache_negative_ttl = 3600
+
+# Space separated list of realms for SASL authentication mechanisms that need
+# them. You can leave it empty if you don't want to support multiple realms.
+# Many clients simply use the first one listed here, so keep the default realm
+# first.
+#auth_realms =
+
+# Default realm/domain to use if none was specified. This is used for both
+# SASL realms and appending @domain to username in plaintext logins.
+#auth_default_realm =
+
+# List of allowed characters in username. If the user-given username contains
+# a character not listed in here, the login automatically fails. This is just
+# an extra check to make sure user can't exploit any potential quote escaping
+# vulnerabilities with SQL/LDAP databases. If you want to allow all characters,
+# set this value to empty.
+#auth_username_chars = abcdefghijklmnopqrstuvwxyzABCDEFGHIJKLMNOPQRSTUVWXYZ01234567890.-_@
+
+# Username character translations before it's looked up from databases. The
+# value contains series of from -> to characters. For example "#@/@" means
+# that '#' and '/' characters are translated to '@'.
+#auth_username_translation =
+
+# Username formatting before it's looked up from databases. You can use
+# the standard variables here, eg. %Lu would lowercase the username, %n would
+# drop away the domain if it was given, or "%n-AT-%d" would change the '@' into
+# "-AT-". This translation is done after auth_username_translation changes.
+#auth_username_format =
+
+# If you want to allow master users to log in by specifying the master
+# username within the normal username string (ie. not using SASL mechanism's
+# support for it), you can specify the separator character here. The format
+# is then <username><separator><master username>. UW-IMAP uses "*" as the
+# separator, so that could be a good choice.
+#auth_master_user_separator =
+
+# Username to use for users logging in with ANONYMOUS SASL mechanism
+#auth_anonymous_username = anonymous
+
+# More verbose logging. Useful for figuring out why authentication isn't
+# working.
+#auth_verbose = no
+
+# Even more verbose logging for debugging purposes. Shows for example SQL
+# queries.
+#auth_debug = no
+
+# In case of password mismatches, log the passwords and used scheme so the
+# problem can be debugged. Enabling this also enables auth_debug.
+#auth_debug_passwords = no
+
+# Maximum number of dovecot-auth worker processes. They're used to execute
+# blocking passdb and userdb queries (eg. MySQL and PAM). They're
+# automatically created and destroyed as needed.
+#auth_worker_max_count = 30
+
+# Host name to use in GSSAPI principal names. The default is to use the
+# name returned by gethostname(). Use "$ALL" to allow all keytab entries.
+#auth_gssapi_hostname =
+
+# Kerberos keytab to use for the GSSAPI mechanism. Will use the system
+# default (usually /etc/krb5.keytab) if not specified.
+#auth_krb5_keytab =
+
+# Do NTLM and GSS-SPNEGO authentication using Samba's winbind daemon and
+# ntlm_auth helper. <doc/wiki/Authentication/Mechanisms/Winbind.txt>
+#auth_use_winbind = no
+
+# Path for Samba's ntlm_auth helper binary.
+#auth_winbind_helper_path = /usr/bin/ntlm_auth
+
+# Number of seconds to delay before replying to failed authentications.
+#auth_failure_delay = 2
+
+auth default {
+ # Space separated list of wanted authentication mechanisms:
+ # plain login digest-md5 cram-md5 ntlm rpa apop anonymous gssapi otp skey
+ # gss-spnego
+ # NOTE: See also disable_plaintext_auth setting.
+ mechanisms = plain
+
+ #
+ # Password database is used to verify user's password (and nothing more).
+ # You can have multiple passdbs and userdbs. This is useful if you want to
+ # allow both system users (/etc/passwd) and virtual users to login without
+ # duplicating the system users into virtual database.
+ #
+ # <doc/wiki/PasswordDatabase.txt>
+ #
+ # By adding master=yes setting inside a passdb you make the passdb a list
+ # of "master users", who can log in as anyone else. Unless you're using PAM,
+ # you probably still want the destination user to be looked up from passdb
+ # that it really exists. This can be done by adding pass=yes setting to the
+ # master passdb. <doc/wiki/Authentication.MasterUsers.txt>
+
+ # Users can be temporarily disabled by adding a passdb with deny=yes.
+ # If the user is found from that database, authentication will fail.
+ # The deny passdb should always be specified before others, so it gets
+ # checked first. Here's an example:
+
+ #passdb passwd-file {
+ # File contains a list of usernames, one per line
+ #args = /etc/dovecot.deny
+ #deny = yes
+ #}
+
+ # PAM authentication. Preferred nowadays by most systems.
+ # Note that PAM can only be used to verify if user's password is correct,
+ # so it can't be used as userdb. If you don't want to use a separate user
+ # database (passwd usually), you can use static userdb.
+ # REMEMBER: You'll need /etc/pam.d/dovecot file created for PAM
+ # authentication to actually work. <doc/wiki/PasswordDatabase.PAM.txt>
+ passdb pam {
+ # [session=yes] [setcred=yes] [failure_show_msg=yes] [max_requests=<n>]
+ # [cache_key=<key>] [<service name>]
+ #
+ # session=yes makes Dovecot open and immediately close PAM session. Some
+ # PAM plugins need this to work, such as pam_mkhomedir.
+ #
+ # setcred=yes makes Dovecot establish PAM credentials if some PAM plugins
+ # need that. They aren't ever deleted though, so this isn't enabled by
+ # default.
+ #
+ # max_requests specifies how many PAM lookups to do in one process before
+ # recreating the process. The default is 100, because many PAM plugins
+ # leak memory.
+ #
+ # cache_key can be used to enable authentication caching for PAM
+ # (auth_cache_size also needs to be set). It isn't enabled by default
+ # because PAM modules can do all kinds of checks besides checking password,
+ # such as checking IP address. Dovecot can't know about these checks
+ # without some help. cache_key is simply a list of variables (see
+ # doc/wiki/Variables.txt) which must match for the cached data to be used.
+ # Here are some examples:
+ # %u - Username must match. Probably sufficient for most uses.
+ # %u%r - Username and remote IP address must match.
+ # %u%s - Username and service (ie. IMAP, POP3) must match.
+ #
+ # The service name can contain variables, for example %Ls expands to
+ # pop3 or imap.
+ #
+ # Some examples:
+ # args = session=yes %Ls
+ # args = cache_key=%u dovecot
+ #args = dovecot
+ }
+
+ # System users (NSS, /etc/passwd, or similiar)
+ # In many systems nowadays this uses Name Service Switch, which is
+ # configured in /etc/nsswitch.conf. <doc/wiki/AuthDatabase.Passwd.txt>
+ #passdb passwd {
+ # [blocking=yes] - See userdb passwd for explanation
+ #args =
+ #}
+
+ # Shadow passwords for system users (NSS, /etc/shadow or similiar).
+ # Deprecated by PAM nowadays.
+ # <doc/wiki/PasswordDatabase.Shadow.txt>
+ #passdb shadow {
+ # [blocking=yes] - See userdb passwd for explanation
+ #args =
+ #}
+
+ # PAM-like authentication for OpenBSD.
+ # <doc/wiki/PasswordDatabase.BSDAuth.txt>
+ #passdb bsdauth {
+ # [cache_key=<key>] - See cache_key in PAM for explanation.
+ #args =
+ #}
+
+ # passwd-like file with specified location
+ # <doc/wiki/AuthDatabase.PasswdFile.txt>
+ #passdb passwd-file {
+ # [scheme=<default password scheme>] [username_format=<format>]
+ # <Path for passwd-file>
+ #args =
+ #}
+
+ # checkpassword executable authentication
+ # NOTE: You will probably want to use "userdb prefetch" with this.
+ # <doc/wiki/AuthDatabase.CheckPassword.txt>
+ #passdb checkpassword {
+ # Path for checkpassword binary
+ #args =
+ #}
+
+ # SQL database <doc/wiki/AuthDatabase.SQL.txt>
+ #passdb sql {
+ # Path for SQL configuration file, see doc/dovecot-sql-example.conf
+ #args =
+ #}
+
+ # LDAP database <doc/wiki/AuthDatabase.LDAP.txt>
+ #passdb ldap {
+ # Path for LDAP configuration file, see doc/dovecot-ldap-example.conf
+ #args =
+ #}
+
+ # vpopmail authentication <doc/wiki/AuthDatabase.VPopMail.txt>
+ #passdb vpopmail {
+ # [cache_key=<key>] - See cache_key in PAM for explanation.
+ # [quota_template=<template>] - %q expands to Maildir++ quota
+ # (eg. quota_template=quota_rule=*:backend=%q)
+ #args =
+ #}
+
+ #
+ # User database specifies where mails are located and what user/group IDs
+ # own them. For single-UID configuration use "static".
+ #
+ # <doc/wiki/UserDatabase.txt>
+ #
+
+ # "prefetch" user database means that the passdb already provided the
+ # needed information and there's no need to do a separate userdb lookup.
+ # This can be made to work with SQL and LDAP databases, see their example
+ # configuration files for more information how to do it.
+ # <doc/wiki/UserDatabase.Prefetch.txt>
+ #userdb prefetch {
+ #}
+
+ # System users (NSS, /etc/passwd, or similiar). In many systems nowadays this
+ # uses Name Service Switch, which is configured in /etc/nsswitch.conf.
+ # <doc/wiki/AuthDatabase.Passwd.txt>
+ userdb passwd {
+ # [blocking=yes] - By default the lookups are done in the main dovecot-auth
+ # process. This setting causes the lookups to be done in auth worker
+ # proceses. Useful with remote NSS lookups that may block.
+ # NOTE: Be sure to use this setting with nss_ldap or users might get
+ # logged in as each others!
+ #args =
+ }
+
+ # passwd-like file with specified location
+ # <doc/wiki/AuthDatabase.PasswdFile.txt>
+ #userdb passwd-file {
+ # [username_format=<format>] <Path for passwd-file>
+ #args =
+ #}
+
+ # checkpassword executable user database lookup
+ # <doc/wiki/AuthDatabase.CheckPassword.txt>
+ #userdb checkpassword {
+ # Path for checkpassword binary
+ #args =
+ #}
+
+ # static settings generated from template <doc/wiki/UserDatabase.Static.txt>
+ #userdb static {
+ # Template for the fields. Can return anything a userdb could normally
+ # return. For example:
+ #
+ # args = uid=500 gid=500 home=/var/mail/%u
+ #
+ # If you use deliver, it needs to look up users only from the userdb. This
+ # of course doesn't work with static because there is no list of users.
+ # Normally static userdb handles this by doing a passdb lookup. This works
+ # with most passdbs, with PAM being the most notable exception. If you do
+ # the user verification another way, you can add allow_all_users=yes to
+ # the args in which case the passdb lookup is skipped.
+ #
+ #args =
+ #}
+
+ # SQL database <doc/wiki/AuthDatabase.SQL.txt>
+ #userdb sql {
+ # Path for SQL configuration file, see doc/dovecot-sql-example.conf
+ #args =
+ #}
+
+ # LDAP database <doc/wiki/AuthDatabase.LDAP.txt>
+ #userdb ldap {
+ # Path for LDAP configuration file, see doc/dovecot-ldap-example.conf
+ #args =
+ #}
+
+ # vpopmail <doc/wiki/AuthDatabase.VPopMail.txt>
+ #userdb vpopmail {
+ #}
+
+ # User to use for the process. This user needs access to only user and
+ # password databases, nothing else. Only shadow and pam authentication
+ # requires roots, so use something else if possible. Note that passwd
+ # authentication with BSDs internally accesses shadow files, which also
+ # requires roots. Note that this user is NOT used to access mails.
+ # That user is specified by userdb above.
+ user = root
+
+ # Directory where to chroot the process. Most authentication backends don't
+ # work if this is set, and there's no point chrooting if auth_user is root.
+ # Note that valid_chroot_dirs isn't needed to use this setting.
+ #chroot =
+
+ # Number of authentication processes to create
+ #count = 1
+
+ # Require a valid SSL client certificate or the authentication fails.
+ #ssl_require_client_cert = no
+
+ # Take the username from client's SSL certificate, using
+ # X509_NAME_get_text_by_NID() which returns the subject's DN's
+ # CommonName.
+ #ssl_username_from_cert = no
+
+ # It's possible to export the authentication interface to other programs:
+ #socket listen {
+ #master {
+ # Master socket provides access to userdb information. It's typically
+ # used to give Dovecot's local delivery agent access to userdb so it
+ # can find mailbox locations.
+ #path = /var/run/dovecot/auth-master
+ #mode = 0600
+ # Default user/group is the one who started dovecot-auth (root)
+ #user =
+ #group =
+ #}
+ #client {
+ # The client socket is generally safe to export to everyone. Typical use
+ # is to export it to your SMTP server so it can do SMTP AUTH lookups
+ # using it.
+ #path = /var/run/dovecot/auth-client
+ #mode = 0660
+ #}
+ #}
+}
+
+# If you wish to use another authentication server than dovecot-auth, you can
+# use connect sockets. They are assumed to be already running, Dovecot's master
+# process only tries to connect to them. They don't need any other settings
+# than the path for the master socket, as the configuration is done elsewhere.
+# Note that the client sockets must exist in the login_dir.
+#auth external {
+# socket connect {
+# master {
+# path = /var/run/dovecot/auth-master
+# }
+# }
+#}
+
+##
+## Dictionary server settings
+##
+
+# Dictionary can be used by some plugins to store key=value lists.
+# Currently this is only used by dict quota backend. The dictionary can be
+# used either directly or though a dictionary server. The following dict block
+# maps dictionary names to URIs when the server is used. These can then be
+# referenced using URIs in format "proxy::<name>".
+
+dict {
+ #quota = mysql:/etc/dovecot-dict-quota.conf
+ #expire = db:/var/lib/dovecot/expire.db
+}
+
+# Path to Berkeley DB's configuration file. See doc/dovecot-db-example.conf
+#dict_db_config =
+
+##
+## Plugin settings
+##
+
+plugin {
+ # Here you can give some extra environment variables to mail processes.
+ # This is mostly meant for passing parameters to plugins. %variable
+ # expansion is done for all values.
+
+ # Quota plugin. Multiple backends are supported:
+ # dirsize: Find and sum all the files found from mail directory.
+ # Extremely SLOW with Maildir. It'll eat your CPU and disk I/O.
+ # dict: Keep quota stored in dictionary (eg. SQL)
+ # maildir: Maildir++ quota
+ # fs: Read-only support for filesystem quota
+ #
+ # Quota limits are set using "quota_rule" parameters, either in here or in
+ # userdb. It's also possible to give mailbox-specific limits, for example:
+ # quota_rule = *:storage=1048576
+ # quota_rule2 = Trash:storage=102400
+ # User has now 1GB quota, but when saving to Trash mailbox the user gets
+ # additional 100MB.
+ #
+ # Multiple quota roots are also possible, for example:
+ # quota = dict:user::proxy::quota
+ # quota2 = dict:domain:%d:proxy::quota_domain
+ # quota_rule = *:storage=102400
+ # quota2_rule = *:storage=1048576
+ # Gives each user their own 100MB quota and one shared 1GB quota within
+ # the domain.
+ #
+ # You can execute a given command when user exceeds a specified quota limit.
+ # Each quota root has separate limits. Only the command for the first
+ # exceeded limit is excecuted, so put the highest limit first.
+ # Note that % needs to be escaped as %%, otherwise "% " expands to empty.
+ # quota_warning = storage=95%% /usr/local/bin/quota-warning.sh 95
+ # quota_warning2 = storage=80%% /usr/local/bin/quota-warning.sh 80
+ #quota = maildir
+
+ # ACL plugin. vfile backend reads ACLs from "dovecot-acl" file from maildir
+ # directory. You can also optionally give a global ACL directory path where
+ # ACLs are applied to all users' mailboxes. The global ACL directory contains
+ # one file for each mailbox, eg. INBOX or sub.mailbox. cache_secs parameter
+ # specifies how many seconds to wait between stat()ing dovecot-acl file
+ # to see if it changed.
+ #acl = vfile:/etc/dovecot-acls:cache_secs=300
+
+ # To let users LIST mailboxes shared by other users, Dovecot needs a
+ # shared mailbox dictionary. For example:
+ #acl_shared_dict = file:/var/lib/dovecot/shared-mailboxes
+
+ # Convert plugin. If set, specifies the source storage path which is
+ # converted to destination storage (mail_location) when the user logs in.
+ # The existing mail directory is renamed to <dir>-converted.
+ #convert_mail = mbox:%h/mail
+ # Skip mailboxes which we can't open successfully instead of aborting.
+ #convert_skip_broken_mailboxes = no
+ # Skip directories beginning with '.'
+ #convert_skip_dotdirs = no
+ # If source storage has mailbox names with destination storage's hierarchy
+ # separators, replace them with this character.
+ #convert_alt_hierarchy_char = _
+
+ # Trash plugin. When saving a message would make user go over quota, this
+ # plugin automatically deletes the oldest mails from configured mailboxes
+ # until the message can be saved within quota limits. The configuration file
+ # is a text file where each line is in format: <priority> <mailbox name>
+ # Mails are first deleted in lowest -> highest priority number order
+ #trash = /etc/dovecot-trash.conf
+
+ # Expire plugin. Mails are expunged from mailboxes after being there the
+ # configurable time. The first expiration date for each mailbox is stored in
+ # a dictionary so it can be quickly determined which mailboxes contain
+ # expired mails. The actual expunging is done in a nightly cronjob, which
+ # you must set up:
+ # dovecot --exec-mail ext /usr/libexec/dovecot/expire-tool
+ #expire = Trash 7 Spam 30
+ #expire_dict = proxy::expire
+
+ # Lazy expunge plugin. Currently works only with maildirs. When a user
+ # expunges mails, the mails are moved to a mailbox in another namespace
+ # (1st). When a mailbox is deleted, the mailbox is moved to another namespace
+ # (2nd) as well. Also if the deleted mailbox had any expunged messages,
+ # they're moved to a 3rd namespace. The mails won't be counted in quota,
+ # and they're not deleted automatically (use a cronjob or something).
+ #lazy_expunge = .EXPUNGED/ .DELETED/ .DELETED/.EXPUNGED/
+
+ # Events to log. Also available: flag_change append
+ #mail_log_events = delete undelete expunge copy mailbox_delete mailbox_rename
+ # Group events within a transaction to one line.
+ #mail_log_group_events =
+ # Available fields: uid, box, msgid, from, subject, size, vsize, flags
+ # size and vsize are available only for expunge and copy events.
+ #mail_log_fields = uid box msgid size
+
+ # Sieve plugin (http://wiki.dovecot.org/LDA/Sieve) and ManageSieve service
+ #
+ # Location of the active script. When ManageSieve is used this is actually
+ # a symlink pointing to the active script in the sieve storage directory.
+ #sieve=~/.dovecot.sieve
+ #
+ # The path to the directory where the personal Sieve scripts are stored. For
+ # ManageSieve this is where the uploaded scripts are stored.
+ #sieve_dir=~/sieve
+}