exim: Add initial configuration.

[matthijs/servers/drsnuggles.git] / etc / exim4 / conf.d / router / 200_exim4-config_primary

diff --git a/etc/exim4/conf.d/router/200_exim4-config_primary b/etc/exim4/conf.d/router/200_exim4-config_primary
new file mode 100644 (file)
index 0000000..8b2bafb
--- /dev/null
+++ b/etc/exim4/conf.d/router/200_exim4-config_primary
@@ -0,0 +1,90 @@
+
+### router/200_exim4-config_primary
+#################################
+# This file holds the primary router, responsible for nonlocal mails
+
+.ifdef DCconfig_internet
+# configtype=internet
+#
+# deliver mail to the recipient if recipient domain is a domain we
+# relay for. We do not ignore any target hosts here since delivering to
+# a site local or even a link local address might be wanted here, and if
+# such an address has found its way into the MX record of such a domain,
+# the local admin is probably in a place where that broken MX record
+# could be fixed.
+
+dnslookup_relay_to_domains:
+  debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain"
+  driver = dnslookup
+  domains = ! +local_domains : +relay_to_domains
+  transport = remote_smtp
+  same_domain_copy_routing = yes
+  no_more
+
+# deliver mail directly to the recipient. This router is only reached
+# for domains that we do not relay for. Since we most probably can't
+# have broken MX records pointing to site local or link local IP
+# addresses fixed, we ignore target hosts pointing to these addresses.
+
+dnslookup:
+  debug_print = "R: dnslookup for $local_part@$domain"
+  driver = dnslookup
+  domains = ! +local_domains
+  transport = remote_smtp
+  same_domain_copy_routing = yes
+  # ignore private rfc1918 and APIPA addresses
+  ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\
+                        172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16 :\
+                       255.255.255.255
+  no_more
+
+.endif
+
+
+.ifdef DCconfig_local
+# configtype=local
+#
+# Stand-alone system, so generate an error for mail to a non-local domain
+nonlocal:
+  debug_print = "R: nonlocal for $local_part@$domain"
+  driver = redirect
+  domains = ! +local_domains
+  allow_fail
+  data = :fail: Mailing to remote domains not supported
+  no_more
+
+.endif
+
+
+.ifdef DCconfig_smarthost DCconfig_satellite
+# configtype=smarthost or configtype=satellite
+#
+# Send all non-local mail to a single other machine (smarthost).
+#
+# This means _ALL_ non-local mail goes to the smarthost. This will most
+# probably not do what you want for domains that are listed in
+# relay_domains. The most typical use for relay_domains is to control
+# relaying for incoming e-mail on secondary MX hosts. In that case,
+# it doesn't make sense to send the mail to the smarthost since the
+# smarthost will probably send the message right back here, causing a
+# loop.
+#
+# If you want to use a smarthost while being secondary MX for some
+# domains, you'll need to copy the dnslookup_relay_to_domains router
+# here so that mail to relay_domains is handled separately.
+
+smarthost:
+  debug_print = "R: smarthost for $local_part@$domain"
+  driver = manualroute
+  domains = ! +local_domains
+  transport = remote_smtp_smarthost
+  route_list = * DCsmarthost byname
+  host_find_failed = defer
+  same_domain_copy_routing = yes
+  no_more
+
+.endif
+
+
+# The "no_more" above means that all later routers are for
+# domains in the local_domains list, i.e. just like Exim 3 directors.