exim: Completely review the exim configuration.

[matthijs/servers/drsnuggles.git] / etc / exim4 / conf.d / router / 200_exim4-config_primary

diff --git a/etc/exim4/conf.d/router/200_exim4-config_primary b/etc/exim4/conf.d/router/200_exim4-config_primary
deleted file mode 100644 (file)
index 8b2bafb..0000000
--- a/etc/exim4/conf.d/router/200_exim4-config_primary
+++ /dev/null
@@ -1,90 +0,0 @@
-
-### router/200_exim4-config_primary
-#################################
-# This file holds the primary router, responsible for nonlocal mails
-
-.ifdef DCconfig_internet
-# configtype=internet
-#
-# deliver mail to the recipient if recipient domain is a domain we
-# relay for. We do not ignore any target hosts here since delivering to
-# a site local or even a link local address might be wanted here, and if
-# such an address has found its way into the MX record of such a domain,
-# the local admin is probably in a place where that broken MX record
-# could be fixed.
-
-dnslookup_relay_to_domains:
-  debug_print = "R: dnslookup_relay_to_domains for $local_part@$domain"
-  driver = dnslookup
-  domains = ! +local_domains : +relay_to_domains
-  transport = remote_smtp
-  same_domain_copy_routing = yes
-  no_more
-
-# deliver mail directly to the recipient. This router is only reached
-# for domains that we do not relay for. Since we most probably can't
-# have broken MX records pointing to site local or link local IP
-# addresses fixed, we ignore target hosts pointing to these addresses.
-
-dnslookup:
-  debug_print = "R: dnslookup for $local_part@$domain"
-  driver = dnslookup
-  domains = ! +local_domains
-  transport = remote_smtp
-  same_domain_copy_routing = yes
-  # ignore private rfc1918 and APIPA addresses
-  ignore_target_hosts = 0.0.0.0 : 127.0.0.0/8 : 192.168.0.0/16 :\
-                        172.16.0.0/12 : 10.0.0.0/8 : 169.254.0.0/16 :\
-                       255.255.255.255
-  no_more
-
-.endif
-
-
-.ifdef DCconfig_local
-# configtype=local
-#
-# Stand-alone system, so generate an error for mail to a non-local domain
-nonlocal:
-  debug_print = "R: nonlocal for $local_part@$domain"
-  driver = redirect
-  domains = ! +local_domains
-  allow_fail
-  data = :fail: Mailing to remote domains not supported
-  no_more
-
-.endif
-
-
-.ifdef DCconfig_smarthost DCconfig_satellite
-# configtype=smarthost or configtype=satellite
-#
-# Send all non-local mail to a single other machine (smarthost).
-#
-# This means _ALL_ non-local mail goes to the smarthost. This will most
-# probably not do what you want for domains that are listed in
-# relay_domains. The most typical use for relay_domains is to control
-# relaying for incoming e-mail on secondary MX hosts. In that case,
-# it doesn't make sense to send the mail to the smarthost since the
-# smarthost will probably send the message right back here, causing a
-# loop.
-#
-# If you want to use a smarthost while being secondary MX for some
-# domains, you'll need to copy the dnslookup_relay_to_domains router
-# here so that mail to relay_domains is handled separately.
-
-smarthost:
-  debug_print = "R: smarthost for $local_part@$domain"
-  driver = manualroute
-  domains = ! +local_domains
-  transport = remote_smtp_smarthost
-  route_list = * DCsmarthost byname
-  host_find_failed = defer
-  same_domain_copy_routing = yes
-  no_more
-
-.endif
-
-
-# The "no_more" above means that all later routers are for
-# domains in the local_domains list, i.e. just like Exim 3 directors.